BlauTHERM 45° Insulated EPP MVHR Ventilation Ducting Bend

In stock
SKU
BTIDB-45-CON
As low as £5.15 £4.29
Selected SKU: %1
Availability: %1

Choose the matching option for your route. Guide ventilation ducting around the building layout with a BlauTHERM 45° bend. The lightweight EPP fitting continues the insulated air path through a shallower change of direction, with matching connections for the adjoining duct lengths.

  • 45° direction change: Choose the actual angle required by the planned route.
  • Built-in insulation: Continue the EPP air path through the fitting.
  • Matching nominal sizes: Select 125mm, 160mm or 200mm to suit the adjoining duct.
  • Light to position: Arrange the bend and measured lengths before final assembly.
  • Push-fit joints: Fully seat clean matching connections.

BlauTHERM

Give the route a shallower turn.

Guide ventilation ducting around the building layout with a BlauTHERM 45° bend. The lightweight EPP fitting continues the insulated air path through a shallower change of direction, with matching connections for the adjoining duct lengths.

CONNECTION OPTION
125mm / 160mm / 200mm
COMPONENT
45° insulated bend
BlauTHERM 45 degree insulated EPP ventilation duct bend

Make space for the right turn.

Make the 45° insulated bend part of a complete, planned installation.

Let the route follow the building.

Use the 45° fitting for the planned offset or shallow turn. Check the complete footprint with nearby pipework, cables and other services before assembly.

Keep the insulation through the turn.

The expanded polypropylene body forms part of the matching insulated system, helping you build the change of direction with ducting and insulation handled together.

45° direction change

Choose the actual angle required by the planned route.

Built-in insulation

Continue the EPP air path through the fitting.

Matching nominal sizes

Select 125mm, 160mm or 200mm to suit the adjoining duct.

Light to position

Arrange the bend and measured lengths before final assembly.

Push-fit joints

Fully seat clean matching connections.

A coordinated route

Plan the bend alongside couplers, supports and the other required fittings.

Put it to work on your project.

Choose the 45° insulated bend for the route and connection arrangement specified for your installation.

BlauTHERM insulated ductwork with matching joints and supports in an installation
BlauTHERM ductwork, matching joints and supports in an installation.

MVHR heat recovery

Plan this 45° insulated bend alongside the main duct layout, equipment connections and commissioning requirements.

Air conditioning

Select the fitting or support for the designed conditioned-air route, checking the connections and available installation space.

Extract ventilation

Coordinate the component with a suitable extract route and provide the support, sealing and access needed for the finished installation.

Match the connection to your route.

Choose the option that matches the connected components and route design.

125mm

Available option
45° insulated bend

BTIDB-45-125

160mm

Available option
45° insulated bend

BTIDB-45-160

200mm

Available option
45° insulated bend

BTIDB-45-200

Plan a matching connector at each 1m duct joint, plus any additional connections needed around the bend and cut sections.

Plan the turn before making the joints.

Check the angle, nominal size and full installed footprint alongside the airflow design.

BlauTHERM 45 degree bend showing its matching circular connections
The original 45° fitting, with matching circular connections at both ends.
  1. Choose the angle and size.

    Confirm that a 45° turn is required and match the nominal diameter to the adjoining ductwork.

  2. Dry-position the route.

    Check the bend footprint, connection engagement and clearance from other services before measuring adjoining lengths.

  3. Complete the matching joints.

    Keep mating surfaces clean and push matching components fully home. Use BTG-500 EPP adhesive where extra strength and rigidity are required.

  4. Support and commission.

    Support the completed route and include bends in the system airflow and pressure-loss design. Check the finished installation during commissioning.

The details for your installation.

Check these details alongside the route design, actual components and fitting instructions.

Connection option
125mm / 160mm / 200mm
Bend angle
45°
Material
Expanded polypropylene (EPP)
Connections
Matching push-fit BlauTHERM components
Use
Planned 45° change of direction
Available product codes
BTIDB-45-125 / BTIDB-45-160 / BTIDB-45-200
Product code
BTIDB-45-CON

Your 45° insulated bend questions, answered.

When should I choose a 45° bend?

Choose it where the planned duct route needs a 45° change of direction. Check the fitting footprint and system design before ordering.

Is this the same as the 90° version?

The fittings make different changes of direction. This is the 45° bend; select the angle that matches the actual route.

How do I match the bend to my duct diameter?

Choose the same nominal BlauTHERM size as the adjoining ductwork: 125mm, 160mm or 200mm.

Does the bend keep insulation through the turn?

Its EPP body forms part of the matching insulated ducting system. Fully assemble the joints and maintain the insulation and sealing required by the installation design.

Can a bend be planned around other services?

Dry-position the full fitting and adjoining connections alongside nearby services. Check assembly space and supports before finalising the route.

Should pressure loss be considered at the turn?

Include the bend and the other route components in the ventilation system design. Select and commission the system against its required airflow.

Can I cut a straight duct to meet the bend?

Measure the required section and make a square, clean cut with a sharp knife. Allow for joint engagement and a matching connector at each required joint.

What makes the assembled turn secure?

Fully seat clean matching connections, add BTG-500 EPP adhesive where extra joint rigidity is required, and provide suitable supports for the ductwork.

© 2025 Blauberg UK Ltd. All rights reserved.